Characteristics of the S-series conventional power supply with unidirectional output,
The advantages are small size, light weight,
The international popular model is 100W 120W 145W 150W 200W 350W
Application:
Widely used in medical equipment, electronic display, LED street lights, home appliances
Huge price advantage, the power price can save up to $5.
More than 2 years of service life, inexpensive.
Leyu 3‰ far beyond the national standard 3%, hate the power supply life too long want to replace the new, do not choose Leyu power
1, small power consumption, high efficiency, switching power supply circuit, transistor V excitation signal under the excitation, alternatively work in the on-off and cut-off on-off switching state, the conversion speed is very fast, the frequency is generally about 50KHz, some advanced technology countries, can do hundreds or nearly 1000KHz.This makes the switching transistor V power consumption is very small, the efficiency of the power supply can be greatly improved, its efficiency can reach 80%.
Switching power supply
2, small size, light weight.It can be seen clearly from the principle block diagram of the switching power supply that there is no light power frequency transformer.Because the dissipated power on the adjusting tube V is greatly reduced, the larger radiator fin is omitted.Because of these two reasons, the switching power supply is small in size and light in weight.
3, the voltage range is wide, the output voltage from the switching power supply is adjusted by the duty ratio of the excitation signal, the change of the input signal voltage can be compensated by frequency modulation or width modulation.In this way, the stable output voltage can be guaranteed when the power frequency network voltage changes greatly.So the switching power supply voltage regulator range is very wide, the voltage regulator effect is very good.
201W Single Output Switching Power Supply S-201 series
High efficiency, high reliability
AC input range selected by switch
100% full load burn-in test
Protections: Short circuit/ Over load/ Over voltage/ Over temperature
Cooling by free air convection
Fixed switching frequency at 25KHz
2 years warranty
SPECIFICATIONS | ||||||||
OUTPUT | ||||||||
Model | S-201-5 | S-201-7.5 | S-201-12 | S-201-13.5 | S-201-15 | S-201-24 | S-201-27 | S-201-48 |
DC Voltage | 5V | 7.5V | 12V | 13.5V | 15V | 24V | 27V | 48V |
Rated Current | 40A | 26.5A | 16.5A | 14.7A | 13A | 8.3A | 7.4A | 4.2A |
Current Range | 0-40A | 0-26.5A | 0-16.5A | 0-14.7A | 0-13A | 0-8.3A | 0-7.4A | 0-4.2A |
Rated Power | 200W | 198.75W | 198W | 198.45W | 198W | 199.2W | 199.8 | 201.6W |
Ripple & Noise | 150mVp-p | 150mVp-p | 150mVp-p | 150mVp-p | 150mVp-p | 150mVp-p | 200mVp-p | 240mVp-p |
Voltage Adj. Range | -10%,+12% | ±20% | -16%,+10% | -12%,+11% | -10%,+20% | -16%,10% | -4%,+18% | -15%,+17% |
Voltage Tolerance | ±2% | ±2% | ±1% | ±1% | ±1% | ±1% | ±1% | ±1% |
Setup, Rise, Hold Up Time | 200ms,100ms,20ms at full load | |||||||
INPUT | ||||||||
Voltage Range | 90~132VAC/180~264VAC selected by switch 47~63Hz; 254~370VDC | |||||||
AC Current | 4.5A/115V 2.5A/230V | |||||||
Efficiency | 79% | 80% | 80% | 81% | 83% | 83% | 84% | |
Inrush Current | 50A/115V 50A/230V | |||||||
Leakage Current | <3.5mA/240VAC | |||||||
PROTECTION | ||||||||
Over Load | 115%~135% | |||||||
Protection type: shut down o/p voltage, recovers automatically after fault condition is removed | ||||||||
Over Voltage | 115%~135% | |||||||
Protection: hiccup mode, recovers automatically after fault condition is removed | ||||||||
Over Temp. | RTH3≥90℃, shut down o/p voltage, recovers automatically after temperature goes down | |||||||
ENVIRONMENT | ||||||||
Working Temp., Humidity | -10℃~+50℃; 20%~90%RH | |||||||
Storage Temp., Humidity | -20℃~+85℃; 10%~95%RH | |||||||
Vibration | 10~500Hz, 2G 10min./1cycle, period for 60min, each along X, Y, Z axes | |||||||
SAFETY | ||||||||
Withstand Voltage | I/P-O/P: 1.5KVAC I/P-FG: 1.5KVAC O/P-FG: 0.5KVAC | |||||||
Isolation Resistance | I/P-O/P, I/P-FG, O/P-FG:100M Ohms/500VDC | |||||||
STANDARD | ||||||||
Safety Standard | Design refer to UL1950 | |||||||
EMC Standard | Design refer to FCC Part15 J Conduction Class A | |||||||
OTHERS | ||||||||
Dimension | 215*115*50mm(L*W*H) | |||||||
Weight | 0.76Kg | |||||||
Packing | 20pcs/16Kg | |||||||
NOTE | ||||||||
1.All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2.Ripple & noise are measured at 20MHz of bandwidth by using a 12” twisted pair-wire terminated with a 0.1μ & 47μ parallel capacitor. 3.Tolerance: includes set up tolerance, line regulation and load regulation |