Products
75W Single Output Industrial DIN Rail Power Supply NDR-75 series
75W Single Output Industrial DIN Rail Power Supply NDR-75 series
Universal AC input / Full range
Protections: Short circuit / Overload / Over voltage/ Over temperature
Cooling by free air convection
Can be installed on DlN rail TS-35/7.5 or 15
UL 508 (industrial control equipment} approved
EN61000-6-2(EN50082-2} industrial immunity level
100% full load burn-in test
3 years warranty
| MODEL |
NDR-75-12 |
NDR-75-24 |
NDR-75-48 |
| DC VOLTAGE |
12V |
24V |
48V |
| RATED CURRENT |
6.3A |
3.2A |
1.6A |
| CURRENT RANGE |
0 ~ 6.3A |
0 ~ 3.2A |
0 ~ 1.6A |
| RATED POWER |
75.6W |
76.8W |
76.8W |
| RIPPLE & NOISE (max.) Note.2 |
80mVp-p |
120mVp-p |
150mVp-p |
| VOLTAGE ADJ. RANGE |
12 ~ 14V |
24 ~ 28V |
48 ~ 55V |
| VOLTAGE TOLERANCE Note.3 |
±2.0% |
±1.0% |
±1.0% |
| LINE REGULATION |
±0.5% |
±0.5% |
±0.5% |
| LOAD REGULATION |
±1.0% |
±1.0% |
±1.0% |
| SETUP, RISE TIME | 1200ms, 60ms/230VAC 2000ms, 60ms/115VAC at full load | ||
| HOLD UP TIME (Typ.) | 60ms/230VAC 12ms/115VAC at full load | ||
| VOLTAGE RANGE Note.6 | 90 ~ 264VAC 127 ~ 370VDC [DC input operation possible by connecting AC/L(+), AC/N(-)] | ||
| FREQUENCY RANGE | 47 ~ 63Hz | ||
| EFFICIENCY (Typ.) |
85.50% |
88% |
89% |
| AC CURRENT (Typ.) | 1.45A/115VAC 0.9A/230VAC | ||
| INRUSH CURRENT (Typ.) | 20A/115VAC 35A/230VAC | ||
| LEAKAGE CURRENT | <1mA / 240VAC | ||
| OVERLOAD | 105 ~ 130% rated output power | ||
| Protection type : Constant current limiting, recovers automatically after fault condition is removed | |||
| OVER VOLTAGE |
14 ~ 17V |
29 ~ 33V |
56 ~ 65V |
| Protection type : Shut down o/p voltage, re-power on to recover | |||
| OVER TEMPERATURE | Protection type : Shut down o/p voltage, re-power on to recover | ||
| WORKING TEMP. | -20 ~ +70℃ (Refer to "Derating Curve") | ||
| WORKING HUMIDITY | 20 ~ 95% RH non-condensing | ||
| STORAGE TEMP., HUMIDITY | -40 ~ +85℃, 10 ~ 95% RH | ||
| TEMP. COEFFICIENT | ±0.03%/℃ (0 ~ 50℃) | ||
| VIBRATION | Component:10 ~ 500Hz, 2G 10min./1cycle, 60min. each along X, Y, Z axes; Mounting: Compliance to IEC60068-2-6 | ||
| SAFETY STANDARDS | UL508, TUV EN62368-1, EAC TP TC 004 approved;(meet EN60204-1) | ||
| WITHSTAND VOLTAGE | I/P-O/P:3KVAC I/P-FG:2KVAC O/P-FG:0.5KVAC | ||
| ISOLATION RESISTANCE | I/P-O/P, I/P-FG, O/P-FG:>100M Ohms / 500VDC / 25℃/ 70% RH | ||
| EMC EMISSION | Compliance to EN55032 (CISPR32), EN61204-3 Class B, EN61000-3-2,-3, EAC TP TC 020 | ||
| EMC IMMUNITY | Compliance to EN61000-4-2,3,4,5,6,8,11, EN55024, EN61000-6-2 (EN50082-2), EN61204-3, heavy industry level, criteria A, EAC TP TC 020 | ||
| MTBF | 486.2K hrs min. MIL-HDBK-217F (25℃) | ||
| DIMENSION | 32*125.2*102mm (W*H*D) | ||
| PACKING | 0.51Kg; 28pcs/15.3Kg/1.22CUFT | ||
| NOTE |
|
||
| 1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature. 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor. 3. Tolerance : includes set up tolerance, line regulation and load regulation. 4. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets EMC directives. |
|||
Write your message here and send it to us
-
60W Single Output Industrial DIN Rail Power Sup...
-
120W Single Output Industrial DIN Rail Power Su...
-
240W Single Output Industrial DIN Rail Power Su...
-
60W Single Output DIN Rail Power Supply MDR-60 ...
-
120W Single Output Industrial DIN Rail Power Su...
-
120W Single Output Industrial DIN Rail Power Su...
